Model features Released on 9 December 2019 - Limited Edition - 28cm x 23cm - Relatively simple rigging - High quality Cartograf decals for 5 aircraft including 5 colour lozenge camouflage - 157 high quality injection moulded plastic parts - Optional radiators, headrest, propellers, flares and 160hp D.III, 180hp D.IIIa & 200hp D.IIIau engines and Albatros D.V & D.Va parts - 11 photo-etched metal detail parts including LMG 08/15 Spandau cooling jackets - Fine in scale rib tape detail - Full rigging diagrams

Johannisthal based Albatros Flugzeugwerke GmbH were responsible for some of the most graceful and effective fighters of the Great War. Their twin gun, semi-monocoque plywood fuselage Albatros D.1, powered by a 160hp Daimler Mercedes D.III engine, arrived at the front in September 1916 and achieved instant air superiority over its main opposition of Nieuport 11 and DH.2 fighters. Followed immediately by the slightly improved D.II and in December 1916 by the much improved D.III, with its V strutted sesqiplane wing greatly influenced by the successful Nieuport fighters. The D.III was more maneuverable than the D.II and its single spar lower ‘half’ wing afforded greater visibility for the pilot but was also the cause of numerous, frequently fatal, structural failures. Despite much effort this problem was never fully resolved. Nevertheless the D.III remained in production well into late 1917.


Even as the excellent D.III went into production plans were underway for its successor, the Albatros D.V. Retaining the wings of the D.III but with aileron controls routed through the upper wing and with a redesigned fuselage completely oval in section, the D.V was arguably the best looking of all Albatros designs. Unfortunately the D.V inherited the lower wing structural failure problem of the D.III and turned out to not be any real improvement over it performance wise either. Despite this, the Albatros D.V and the D.Va (with aileron controls cables reverted to D.III configuration), were manufactured in greater numbers than any previous German fighter of the war (only surpassed later by the Fokker D.VII, of which Albatros manufactured the great majority).


The Albatros D.V weighed 620kg empty when production commenced in April 1917 but, following strengthening, the empty weight had increased to 680kg before production of the D.Va started in August 1917. While Johannisthal built D.Va remained 680kg throughout production, those ordered from Ostdeutsche Albatros Werke (OAW) in September-October 1917 weighed in at 717kg empty, almost 100kg heavier than the initial D.V. When the Albatros D.V started appearing at the front in May 1917 it was effectively outclassed by the improved SE.5a, Sopwith Camel and SPAD fighters being fielded by the allies at the time. Even after the introduction of the superb Fokker D.VII the Albatros D.V and D.Va could still be found equipping front line Jastas, although most had been relegated to training or home defense duties by the time of the Armistice. Note that these instructions illustrate parts to build Johannisthal built Albatros D.V & D.Va and Ostdeutsche Albatros Werke (OAW) built D.Va. Please make sure you take note of the different parts required for your chosen decal scheme. Any history of this important aircraft here is of necessity very brief, therefore we encourage you to seek out any, or all, of the reference books mentioned below for a more thorough understanding. 


WW1 colour schemes are contentious at the best of times and we have done our best to provide what we consider to be accurate painting information for this model. The colourful unit and personal markings applied to the various German fighters of the Great War have attracted more than their fair share of debate over the years and, while we have been as meticulous as we could be, I’m sure some will not find our choices to their liking. Albatros D.V/D.Va fuselages were usually clear varnished resulting in a yellowish plywood colour. The fabric covered wings and tailplane were finished in either of 2 ways, painted (with medium grey green & mauve or dark grey green & lilac on top with light blue below) or covered in pre-printed lozenge camouflage fabric, some of which was almost certainly overpainted with a transparent (brown?) glaze to tone down the vibrant colours. Metal fittings were painted in pale grey-green, as was much of the engine bay. Exterior metal panels and fittings were usually painted in this same pale grey-green colour although some late production D.Va were finished in a darker grey-green colour. There was considerable freedom for German units to apply their own colour schemes to their aircraft with some using drab camouflage paints, usually applied with a "loofah" type sponge, while others preferred highly visible colours to aid identification at a distance. Additionally individual pilot"s markings were also applied in a fashion dictated by the unit commander.
Wingspan:Length:Max Weight:Max Speed:
9.00m (29’ 6”)7.33m (24’ 0.5”)755kg - 937kg170kph (106mph)
No Manufactured:Production:Engine:Ceiling:
D.V 900/D.Va 1662 April 1917 – early 1918160-180-200hp Daimler-Mercedes D.III/IIIa/IIIaü6250m (20500’)
2x 7.92mm LMG 08/15 ‘Spandau’
Windsock Datafile 3 Albatros D.V, Ray Rimell, 1987 – Albatros Fighters Windsock Datafile Special, Ray Rimell, 1991 – Squadron Signal Albatros Fighters in Action, John F Connors, 1981 – Australian War Memorial Museum, Canberra, Australia – The Vintage Aviator LTD - 1914-18 Aviation Heritage Trust – Private Collections.